|1||Dimension and weight||115.9mmx95.5mmx69.3mm;480g|
|2||External diameter of outlet||27mm|
|3||External diameter of inlet||27mm|
|4||Driving mechanism||Brush-less, magnetic isolated design|
|5||Material of pump shell||ABS,PES/SPS/PPS/PA66+30%GF (Optional)|
|6||Condition of use||Can continuously work, submersible or land use (not self-priming)|
|7||Suitable medium||Water, oil, or normal acid/ alkaline liquids|
(Pre-test needed for special liquid)
|8||Max working temperature||60℃(for T sub-series) or 100℃(for S/A sub-series)|
|9||Power consumption||2.5W~48W(for T sub-series) or 2.5W~86.4W(for S/A sub-series)|
|10||Rated voltage||12Vdc or 24Vdc|
|11||Working voltage range||5Vdc ~ 14Vdc or 5Vdc ~ 26Vdc|
|12||Max load current||2.0A (for T sub-series) or 4.5A(for S/A sub-series)|
|13||Max horizontal flow rate||52L/MIN(for T sub-series) or 60L/MIN(for S/A sub-series)|
|14||Max static lift||3.5M(for T sub-series) or 5M(for S/A sub-series) |
|16||Waterproof class||IP68(suitable for submersible installation)|
|17||Life span||>30,000hrsIP68(suitable for submersible installation)|
|18||Power supply||Suitable solar panel, batteries, adapter or other power source|
|19||Protection function||dry-run protection, lock protection(customized function)|
|20||Power regulation function||Speed adjustable by PWM signal, 0~5V analog signal or potentiometer (functions are optional for customization)|
small size with high efficiency,maintenance-free
Use ceramics shaft and carbon fiber sleeve
Completely water proof (IP68)
Brush-less dc control without pollution, long life span
OEM and ODM service accept
Offer Pump related control system design
Electrical parameters (only for reference，parameters can be customized for specific requirements)
|Model No.||Voltage||Max load current||Max static lift||Max flow rate||Power consumption|
Information including continuous working time, working temperature and medium is required to be pre-confirmed with professionals; pump cannot work with high temperature or corrosive fluids.
When pump is connected into circulation system, load current will be reduced to 70~85% of Max working current (opening outlet current).
The head means the Max vertical lifting height of water,the flow is 0L/MIN@max head.
The max flow rate means flow rate with no lifting height(according to the curve bellow)
Difference between 2phase & 3phase brushless DC pump
| Hall sensor driving, circuit board should be placed inside pump body|
NOTE that 3phase dc is completely different with 3phase AC; 3phase DC means 3 pairs of magnetic polarity & sensor-less, power supply the same with common DC pump
Intelligent program-driving, sensor-less, circuit outside of pump body (main factor that pump can be high-temperature resistant)
Speed adjustable by PWM, 0~5V signal or potentiometer(optional)
Lock protection,reverse-connected protection, over-vol.&over-current protection,
Soft start, no current impact, can be contact directly with solar panel
Potentiometer Speed adjusting connection:
Contact the red and black wire to both ends of potentiometer(variable resistor),then contact the yellow wire to the middle of potentiometer,Speed canbe changed by turning the potentiometer. Potentiometer speed adjusting is the same with VR speed adjusting(Remove the potentiometer and contact the speed adjusting wire like VR speed adjusting connection bellow).
PWM(50-800HZ/Amlitude 5V) or VR(0-5V) Speed adjusting connection:
Contact the yellow wire to the control system's speed control signal output interface(PWM or VR) and contact the black wire to the ground lead in the control system.hang the red wire on the air.
Dimensions of pump
Characteristics of three-phase water pump
1.DC Low voltage safe and reliable
2.Three phase brushless sine wave control technology
3.Eliminate high-frequency electromagnetic noise, smooth and silent
4.The pump body and the drive can be separated and resistant to high temperature
5.Magnetic isolation design, leakage proof, waterproof grade IP68.
6.Acid, alkali and salt corrosion resistance, oil resistance, organic solvents and other liquid media (consult in advance)
7.Constant power can be customized (for example, 12V 80W water pump, Constant Power 80W with voltage varying between 12v-24v)
8.Constant speed can be customized (keep the speed unchanged when the load changes)
9.Accurate dry run protection and Jam protection based on current detection (programmable protection mechanism)
10.Soft start eliminates the peak voltage and reduces the starting current
11.Suitable for Music fountain and other high-frequency start- stop application
12.MPPT function can be customized for solar power supply to avoid poor startup when the light is weak.
13.The pump and pump control system can be customized for various application environment requirements