Specifications
| NO. | Item | Specs |
| 1 | Dimension and weight | 93.9mmx99.5mmx69.6mm;480g |
| 2 | External diameter of outlet | 1/2” thread(M20) |
| 3 | External diameter of inlet | 1/2” thread(M20) |
| 4 | Driving mechanism | Brush-less, magnetic isolated design |
| 5 | Material of pump shell | ABS,PES/SPS/PPS/PA66+30%GF (Optional) |
| 6 | Condition of use | Can continuously work, submersible or land use (not self-priming) |
| 7 | Suitable medium | Water, oil, or normal acid/ alkaline liquids
(Pre-test needed for special liquid) |
| 8 | Max working temperature | 60℃(for T sub-series) or 100℃(for S/A sub-series) |
| 9 | Power consumption | 2.5W~48W(for T sub-series) or 2.5W~86.4W(for S/A sub-series) |
| 10 | Rated voltage | 12Vdc or 24Vdc |
| 11 | Working voltage range | 5Vdc ~ 14Vdc or 5Vdc ~ 26Vdc |
| 12 | Max load current | 2.0A (for T sub-series) or 4.5A(for S/A sub-series) |
| 13 | Max horizontal flow rate | 18L/MIN(for T sub-series) or 26L/MIN(for S/A sub-series) |
| 14 | Max static lift | 8M(for T sub-series) or 15M(for S/A sub-series) |
| 15 | Noise class | <40dB |
| 16 | Waterproof class | IP68(suitable for submersible installation) |
| 17 | Life span | >30,000hrsIP68(suitable for submersible installation) |
| 18 | Power supply | Suitable solar panel, batteries, adapter or other power source |
| 19 | Protection function | Dry-run protection, lock protection(customized function) |
| 20 | Power regulation function | Speed adjustable by PWM signal, 0~5V analog signal or potentiometer (functions are optional for customization) |
| 22 | Feature | small size with high efficiency,maintenance-free Use ceramics shaft and carbon fiber sleeve Completely water proof (IP68) Brush-less dc control without pollution, long life span OEM and ODM service accept Offer Pump related control system design
|
Electrical parameters (only for reference，parameters can be customized for specific requirements)
| Model No. | Voltage | Max load current | Max static lift | Max flow rate | Power consumption |
| V(dc) | A | M | L/H | w |
| DC50E-12110S | 12 | 4.5 | 11 | 1320 | 52 |
| DC50E-12110A |
| DC50E-24150S | 24 | 3.30 | 15 | 1560 | 83 |
| DC50E-24150A |
| NOTE | Information including continuous working time, working temperature and medium is required to be pre-confirmed with professionals; pump cannot work with high temperature or corrosive fluids. When pump is connected into circulation system, load current will be reduced to 70~85% of Max working current (opening outlet current). The head means the Max vertical lifting height of water,the flow is 0L/MIN@max head. The max flow rate means flow rate with no lifting height(according to the curve bellow)
|
Difference between 2phase & 3phase brushless DC pump
2phase
(T sub-series) | Hall sensor driving, circuit board should be placed inside pump body |
3phase
(S/A sub-series) | NOTE that 3phase dc is completely different with 3phase AC; 3phase DC means 3 pairs of magnetic polarity & sensor-less, power supply the same with common DC pump Intelligent program-driving, sensor-less, circuit outside of pump body (main factor that pump can be high-temperature resistant) Speed adjustable by PWM, 0~5V signal or potentiometer(optional) Lock protection,reverse-connected protection, over-vol.&over-current protection, Soft start, no current impact, can be contact directly with solar panel
|
Potentiometer Speed adjusting connection:
Contact the red and black wire to both ends of potentiometer(variable resistor),then contact the yellow wire to the middle of potentiometer,Speed canbe changed by turning the potentiometer. Potentiometer speed adjusting is the same with VR speed adjusting(Remove the potentiometer and contact the speed adjusting wire like VR speed adjusting connection bellow).
PWM(50-800HZ/Amlitude 5V) or VR(0-5V) Speed adjusting connection:
Contact the yellow wire to the control system's speed control signal output interface(PWM or VR) and contact the black wire to the ground lead in the control system.hang the red wire on the air.
